Blue Ink is member of Ultimheat Alliance Controls and heating equipments

Blue Ink is member of Ultimheat Alliance Controls and heating equipments

Select language

Controls, Components, Heating equipments

ULTIMHEAT® GROUP PRODUCTS

Type Y0308G

“Pigtail” bulb room thermostat.

Main features: Ambient temperature control in professional premises where good protection against liquid splashes or dust is requested. Adjustment ranges: 4-40°C (40-105°F). Contact: SPDT

Type Y0D

“Pigtail” bulb room thermostat, with built-in pilot light.

Main features: Ambient temperature control in professional premises where good protection against liquid splashes or dust is requested.Adjustment ranges: 4-40°C (40-105°F). Contact: SPNC (open on temperature rise). One terminal is available for neutral connection. SPDT contact available on request but it is not compatible with neutral terminal and pilot light

Type Y0A

Bulb and capillary thermostat, for heat control, with built-in pilot light.

Main features: Distance temperature control in professional premises where good protection against liquid splashes or dust is requested. Adjustment ranges: -35+35°C (-30+95°F), 4-40°C (40-105°F), 30-90°C (85-195°F), 30-110°C (90-230°F), 50-200°C (120-390°F),50-300°C (120-570°F) Capillary length: 1.5 m Contact: SPNC (open on temperature rise). One terminal is available for neutral connection. SPDT contact available on request but it is not compatible with neutral terminal and pilot light.

Type Y0B

Rod thermostat, for heat control, with built-in pilot light. Stainless steel or nickel plated brass pocket

Main features: emperature control of tanks or pipes in professional premises where good protection liquid splashes or dust is requested. Adjustment ranges: -35+35°C (-30+95°F), 4-40°C (40-105°F), 30-90°C (85-195°F), 30-110°C (90-230°F) Rod length: 90, 230, 300 mm. Other length on request Contact: SPNC (open on temperature rise). One terminal is available for neutral connection. SPDT contact available on request but it is not compatible with neutral terminal and pilot light.

Types Y06 (With ½”BSPT nickel plated brass pocket) and Y07 (AISI 304 pocket, ½”BSPP)

Combination of adjustable set point thermostat and manual reset high limit

Main features: Temperature control and safety on storage water heaters, solar heating tanks, boilers Adjustment ranges: 0-60°C (32-140°F) ; 30-90°C (85-195°F); 30-110°C (90-230°F) Pocket length (L): 205mm (standard), 170, 300, 450 and 600mm on request Manual reset thermostat contact: Failsafe, open by temperature rise; 16A (2,6) 250V alt.

Type Y08

Combination of adjustable set point thermostat and manual reset high limit,With immersion heater mounting bracket

Main features: Temperature control and safety on storage water heaters, solar heating tanks, boilers Control sub-assembly designed to be fitted, directly on standard immersion heaters. Power up to 3500W, 230V, single phase. Adjustment ranges: 0-60°C (32-140°F) ; 30-90°C (85-195°F) ; 30-110°C (90-230°F) Manual reset thermostat contact::Fail safe,open by temperature rise; 16A (2,6) 250V alt

Type Y09

Combination of adjustable set point thermostat and manual reset high limit, capillary output, wall mounting

Main features: Control sub assembly designed to be used directly on standard immersion heaters, power up to 3500W, 230V, single phase. Adjustment ranges: 0-60°C (32-140°F) ; 30-90°C (85-195°F) ; 30-110°C (90-230°F) Capillary lengths (C): 900 mm Manual reset thermostat contact::Fail safe,open by temperature rise; 16A (2,6) 250V alt.

Type 72

Dia. 10 mm cartridge thermostat with ½" or M14x1.5 fitting

Main features: Detection of a temperature value in liquids, water, hydraulic oils, thermal oils. Probe material: 304 stainless steel sheath diameter 10mm, with AISI 304 fitting.Calibration temperature: 50 to 120°C(100 pcs MOQ applicable for specific values).Contact: open by temperature rise. (Close on temperature rise possible on creep action models)

Type UWJ

Temperature limiter for explosive gas atmospheres.

Main features: Motor thermal protection, heat tracing, alarm and high temperature safety in explosive gas atmospheres.Classification: Ex mb IIC (Gaz) and Ex tb IIC (Dust) (Testing certificates: ATEX INERIS 15ATEX0018X and IECEx INE 15.0022X).Ambient temperature limits on enclosure : -40 to +150°C Set point: fixed factory set minimum 50°C maximum 150°C. (Calibration values are always zero current values).

Type 49C

Thermostats overmolded on heat tracing cables

Main features: Overmolding a disc thermostat on a heating cable allows to switch it on when the room temperature falls below a certain threshold,and to switch it off when the temperature rises.Contact: Open by temperature rise.Calibration temperatures: Available on request (minimum of start of production 1000 pieces applicable for specific values).

Type 4REMR

Waterproof manual reset disc thermostats

Main features: Manual reset safety thermostats, for applications where there are risks of condensation or water drops. Contact: SPNC, open on temperature rise. Reset: ManualCalibration temperatures: Available on request from 40 to 120°C. Standard tolerances +/- 5 ° C. MOQ 1000 pieces applicable for specific values.

Type WQD

Wood and solid fuel stove damper bulb and capillary thermostat

Main features: This thermostat is an automatic control of wood, pellets, coal or anthracite fired solid fuel appliances like room heaters, boilers, stoves, central heating units.Temperature Ranges:-Room Air Control 4/40°C (40/105°F).-Hot water 30/90°C (85/195°F)).-Flue temperature 50/300°C (120/570°F).Other temperature ranges and displacement available on request (MOQ apply)

Type 8GB060500

Bulb and capillary thermostat, temperature range 60-500°C

Main features: Thermostats for furnaces and ovens which the operating temperature is higher than 320°C, such as pizza ovens. temperature range 60-500°CBulb and capillary: Stainless steel. Capillary minimum bending radius 5 mm.Contact: SPDT

Type LS

Additional thermostat shaft rotary switch

Main features: These on-off switches are designed to be added on thermostat shafts.Shaft lengths available: 11.5;15; 23mmElectrical rating: 20A 250/ 400V res.Rotation: can be used on thermostats with 180 to 310° angular shaft rotation

Types BE2, BE3, BE5, BE6

Elevated terminal connection blocks

Main features: In electrothermal connection applications, especially in immersion heaters connection boxes appear specific constraints: highambient temperature, frequent thermal cycles, and confined space around the ends of the heating elements and their terminals,making difficult to the user to make connections. These terminals have been developed to address these constraints.Body: Glass-filled Polyamide 66, UL94V, GWFI 960°C, ambient temperature up to 150°C.Voltage: 400V max.

Types Y301UC2EA2, Y307E, Y308E

PA66 enclosures for immersion heaters

Main features:Immersion heater connectionsHousing: IP54, black PA66, fiberglass reinforced, UL94V0. High impact and UV resistance. They have a silicone foam covergasket.Cable gland: PA66.

Type Y6TP

Wire end silicone boots, silicone gel improved waterproofing, for heat tracing

Main features:The sealing of the free end of the heating cables. Boot material: UL 94-VO, black silicone (other colors on request). Temperature resistance 220 ° C. Filling material: silicone gel filling 50% of the internal volume of the boot. Insulation resistance 1.1×1015 Ω•cm @500V.Temperature resistance -60 + 260°C.Needle penetration (1/10mm): 70

Type 9BF

Thermostat and temperature sensor boots

Main features:They are designed to protect thermostats or temperature sensors against accidental contact or liquid ingress.Flammability: UL 94-V0Hardness: 60 Shore AColor: black or orange depending on the model. Other colors available (MOQ apply)

Type IB

Surface mounting thermostats.

Main features:Precise and adjustable surface temperature control on heating plates, silicone heating pads, foil heaters, temperature range from 20 to 300°

Type 35ER

Energy regulators

Main features:Energy regulators are used to adjust power on electrical heaters. Connected in line with electrical heaters, they provide adjustable cycling sequence, thus adjusting average electrical power

Type 8G

Single pole control bulb and capillary thermostat.

Main features:Adjustable remote temperature control. Liquid filled bulb. Numerous temperature range from -35°C to +320°C used in single pole circuit

Type 8C

3 pole control bulb and capillary thermostats.

Main features:Adjustable remote temperature control. Liquid filled bulb. Numerous temperature range from -35°C to +320°C used in 3 poles circuits

Type 1B

Rod thermostats.

Main features:Temperature control of liquids and gas, with DPST or SPDT contact. Numerous temperature range from -10°C to +165°C

Type 2PE

Electronic thermostat.

Main features:This electronic thermostat for incorporation has been designed to replace electromechanical thermostats. It is mounted with two screws M4 at the same distance 28 mm, uses a 6mm dia. shaft with 4.6mm flat with the same length, and its rotation angle is 270 °. The temperature ranges are the same as the bulb and capillary thermostats.It additionally features adjustable temperature differential, and heating or cooling relay output setting, and control or manual reset action can be set.

Type 2DN

Digital display electronic controller.

Main features:This electronic temperature controller with the simplest and the most instinctive setting by end user was designed for easy incorporation inside cabinets with DIN rail mounting. It can be used by untrained operators. It provides simple On Off action temperature control.End user has access to set point and differential setting only.It is possible to set °C or °F display, heating or cooling relay output, decimal display, sensor type and temperature range by internal Dip switches (Without access by end user).Adjustment of maximum temperature can be set without need to open the control.Pt100 and NTC sensors

Type 4C

3 pole manual reset disc thermostats.

Main features:Temperature limit of heaters, instant water heaters, saunas steam generators, industrial heaters. Used in 3 pole circuits

Type 82

3 pole manual reset high limit thermostat.

Main features:Fail safe, manual reset, with capillary length 250mm or 900 mm, 3 pole contacts open on temperature rise temperature range from 60°C to 170°C

Type LS

Additional thermostat shaft switch, 20A 250-400V

Main features:These on-off switches are designed to be added on thermostat shafts. They provide off position when the thermostat shaft is at the minimum position. They are available in single pole contact, two pole (one level) and three pole or four-pole contact (two levels).

Type LT

LT Type On-off rotary switch, 20A 250-400V

Main features:These on-off switches are designed for heater power switching. They are available in single pole contact, two pole (one level) and three pole or four-pole contact (two levels).

Type K

Professional applications bulb and capillary thermostat.

Main features:Heavy duty , temperature ranges up to 760°C, SPDT 15A 250-400V. Also exists with SPDT manual reset.

Type Y02N

Cabinet thermostat DIN rail mounting.

Main features:These models have been designed to control the temperature inside electrical cabinets, being mounted on their DIN rail. Their SPDT contact allows their use to control a cabinet heater, a fan or a filter fan, or a cooling system. Temperature range -10+50, to +20+80°C

Type Y03

IP44 housing bulb and capillary thermostat.

Main features:SPDT contact, external knob, liquid filled bulb, distance measurement with capillary. Adjustment ranges: -35+35°C (-30+95°F), 4-40°C (40-105°F), 30-90°C (85-195°F), 30-110°C (90-230°F), 50-200°C (120-390°F), 50-300°C (120-570°F) Mounting:Wall mounting, by two side lugs with holes for dia.4 mm screws, 62 mm distance.

Type Y04

IP44 housing rod thermostat.

Main features:SPDT contact, external knob, liquid filled rod, located inside a backside mounted 304L stainless steel pocket. Adjustment ranges: --35+35°C (-30+95°F), 4-40°C (40-105°F), 30-90°C (85-195°F), 30-110°C (90-230°F) Mounting: by the ½”BSPT pocket fitting

Type Y05

IP44 housing rod thermostat, for swimming pools.

Main features:SPDT contact, external knob, liquid filled rod, located inside a backside mounted plastic pocket. Adjustment ranges: -4-40°C(40-105°F) Mounting: by the ½”NPT pocket fitting

Type Y1A

IP65 aluminum enclosure ambient temperature thermostat.

Main features:Wall mounting for indoor temperature control of cold room - Temperature control of industrial or commercial premises. - Outdoor temperature control of antifreeze heaters, - Green houses and livestock stables temperature control Withstand very low ambient temperatures Temperature range: -numerous from-25 to +70°C

Type Y1GK

IP65 aluminum enclosure bulb and capillary thermostat.

Main features:Remote control in usual industrial application and environment, not hazardous areas.Internal adjustment is convenient for products that must not be frequently adjusted. Withstand very low ambient temperatures Long electrical and mechanical life model Temperature range: -numerous from -25 to +760°C

Y1G8

IP65 aluminum enclosure bulb and capillary thermostat.

Main features:Remote control in usual industrial application and environment, not hazardous areas.Internal adjustment is convenient for products that must not be frequently adjusted.Standard electrical and mechanical life model Temperature range: -numerous from -35 to +320°C

Y1R8

IP65 aluminum enclosure Rod thermostat.

Main features:These liquid expansion rod thermostats can be installed inside pockets as immersion thermostats in pipelines and containers, and for monitoring temperature in air ducts, in usual industrial application and environment. (Not suitable for hazardous areas). - Internal adjustment is convenient for products that must not be frequently adjusted. - Insensibility to strong vibrationsStandard electrical and mechanical life model Temperature range: -numerous from 4 to +350°C

Y108

IP65 aluminum enclosure, for pipes, surface temperature control.

Main features:Pipe surface temperature control in usual industrial application and environment, (Not suitable for hazardous areas)Internal adjustment is convenient for products that must not be frequently adjusted.Standard electrical and mechanical life model

Type Y22

Thermostats with IP65 plastic housings, for heat tracing.

Main features:PIn these boxes, the thermostat, bimetal disc type, is over-molded, and is thermally insulated from the wall on which it is mounted.Its temperature sensing cup is mechanically protected by a grid. It is located in front of the enclosure to be in an area of natural circulation of air.

Type Y303

Immersion heaters connection boxes 78x66x50 mm.

Material:Die cast aluminum Type:Universal, unlosable stainless steel fasteners, galvanic corrosion protected

Type Y304

Immersion heaters connection boxes 78x78x74 mm.

Material:Die cast aluminum Type:Unlosable stainless steel fasteners, galvanic corrosion protected

Type Y305

Immersion heaters connection boxes 105x105x96 mm.

Material:Die cast aluminum Type:Universal, unlosable stainless steel fasteners, galvanic corrosion protected

Type Y306

Immersion heaters connection boxes Dia. 100x100 mm.

Material:Fiber glass reinforced PA66 Type:Universal, unlosable stainless steel fasteners

Type Y309

Immersion heaters connection boxes 182x132x144 mm.

Material:Die cast aluminum Type:Universal, unlosable stainless steel fasteners Many versions of this box size, fully equipped and wired are described in the catalog No. 3, series Y7.

Type Y5F

Hand held or wall mounting digital temperature controller.

Main features:This control box has the smallest footprint and the lowest price of the Y range with waterproof enclosure. It has a modern and aesthetic design, and the same professional concept than other products of this range.Because of their small size (120 x 70 x 40 mm), these controls can be wall mounted with 2 screws 55 mm distance, hand held or just simply laid on the working table.

Type 9BBJO

Silicone boots and grommets for applications in heating equipment and thermostats boots.

Thermostats boots Main features:They are designed to protect thermostats against accidental contact or liquids ingress. Depending on the model, they can be filled with resin or simply be glued or vulcanized on their support

Type 9BBRA

Immersion heaters brass fittings.

Main features:- Fittings for incorporation by immersion heater manufacturers - Fit the full range of immersion heater enclosures- Compact size and short length result in reduced weight ( save + / -30% compared to double thread fittings) - The fitting thread lengths allow throw wall mounting with fiber gasket and nut on wall of 6 mm thickness (9 mm for 2” and above) or on threaded socket with gasket - Allows a 360° rotation of enclosure when mounted with their rotation ring

Types Y6,Y7,Y8

Industrial temperature controls.

Main features:These products come in 4 different dimensional configurations, in control (One sensor) or control + high limit safety (2 sensors or one sensor + one bulb) electronic or thermostat control Temperature range: numerous from -35 to +760°

Type 273

Electronic intelligent controller, on off action.

Main features:Mini-sized and integrated intelligent controller, with very simple end-user interface: Change of set point is made without password, with up and down keys. 10 or 16A output relay. 220 - 240V power supply Sensor: NTC, Pt100, K thermocouple

Type KAA

Explosion proof bulb and capillary thermostats for incorporation Temperature control, front mounting.

Main features:These thermostats are intended to monitor or control temperatures in hazardous areas.They can be used in zones 1 or 2 with gas, smoke and fog, class IIC, surface temperature T6, and for ambient temperature on housing of -50 to +80°C.This thermostat uses a flameproof micro-switch type II2Gb, Ex dIIC .The thermostat must be installed in an increased safety enclosure, type Ex-“e”, and electrical connections at the end of the wires must be made inside this EX-“e”enclosure.The thermostat capillary exit must be performed by a cable gland with gasket adapted to the diameter of the capillary and providing the level of protection required by the standard. Temperature range: numerous from -25 to +300°CExists also with DIN rail mounting

Type Y90-G

Explosion proof thermostats with IP54 aluminum enclosure, cable output Bulb and capillary thermostat, SPDT, 5A 250V, cable connection.

Main features:This thermostat uses a flameproof micro-switch type Ex II2G (Ex dIIC T6 Gb). It is installed in a waterproof aluminum enclosure with an ingress protection class IP54, grey epoxy painted RAL 7032, fitted with a built in electrical connection cable. It is not allowed to make electrical connections inside this aluminum enclosure. Electrical connection at the end of this cable must be made inside an increased safety "e" junction box complying with the standard EN60079-7, or outside hazardous area. Aluminum enclosure earthing is mandatory. Temperature range: numerous from -25 to +300°C

Type Y94

Explosion proof thermostats and limiters, connection inside EX « e » aluminum housing with built-in connection block. Bulb and capillary thermostat.

Main features:They are intended to monitor or control the temperatures in hazardous areas. Thermostat, housing and terminal block are indivisible.In gas explosive atmospheres, they can be used in zones 1 or 2 in the presence of gas, smoke and fog, class IIC, surface temperature T6, and ambient temperature on the enclosure from -50 to +60°C or from-50 to +70°C In dust explosive atmospheres, they can be used in zones 21 and 22These thermostats have explosion-proof microswitch type II2Gb, Ex dIIC according to IEC/EN 60079-1, embedded in an increased safety aluminum enclosure according to IEC/EN 60079-7. Temperature range: numerous from -25 to +300°C

Type Y96

Explosion proof thermostats and limiters, connection inside EX « e » aluminum housing with built-in connection block. Rod thermostat.

Main features:They are intended to monitor or control the temperatures in hazardous areas. Thermostat, housing and terminal block are indivisible.In gas explosive atmospheres, they can be used in zones 1 or 2 in the presence of gas, smoke and fog, class IIC, surface temperature T6, and ambient temperature on the enclosure from -50 to +60°C, or from -50 to +70°C.In dust explosive atmospheres, they can be used in zones 21 and 22These thermostats have explosion-proof microswitch type II2Gb, Ex dIIC according to IEC/EN 60079-1, embedded in an increased safety aluminum enclosure according to IEC/EN 60079-7. Temperature range: numerous from -25 to +300°C

Type ZE

Positive pressure switches, for printed circuit, creep action contact.

Main features:Electronic printed circuit. This pressure switch is more sensible than snap action models and can be calibrated at lower pressure values. Very small differential.

Type ZA

Positive pressure switches, creep action contact.

Main features:Electronic circuits. Pressure sensing on water heaters. This pressure switch is more sensible than snap action models and can be calibrated at lower pressure values. Very small differential.

Type ZQ

Snap action contact miniature pressure switch. Rating up to 25A

Main features:Pressure sensing on water heaters, boilers, and electrical appliances.

Type ZW

Snap action double pole contact miniature pressure switch.

Main features:Pressure sensing on water heaters, boilers, and electrical appliances.

Type MA1

Snap action contact pressure switch, field adjustable, IP65 housing.

Main features:Pressure sensing on water heaters, boilers, spas and swimming pool heaters and filters, electrical appliances used outside.

Type MN3

Snap action contact pressure switch, field adjustable, 3 contacts.

Main features:Pressure sensing on water heaters, boilers, spas and swimming pools heaters and filters, electrical appliances (For incorporation).

Type ZH

Differential pressure switch for printed circuits.

Main features:Electronic printed circuits. Detection of low positive, negative or differential pressure. Measurement of liquid levels, air flow, filters efficiency. Very small differen¬tial, about 2 millibars

Type ZP

Snap action contact airswitch.

Main features:Direct actuating of pumps and blowers in spas and swimming pools, sink erasers, professional or home appliances used with risks of water splashing. Resist to spas and swimming pools ozone concentration.

Type 66ZM5

Air buttons (air transmitters).

Main features:Remote operation of air switches. This pneumatic switching technology safely isolates the user from the electrical current. The air transmitters provide the pulse air pressure needed to operate a remote air switch Typical applications:Spas , swimming pools, electrical equipment remote operating of electrical devices on/off including motors, lights, pumps, air blowers, or other associated equipment. Operating distance: With appropriate tubing, these hand actuation transmitters can operate air switches from distances of up to 30 meters (100 feet.)

Type 66ZMD

Foot air pedal (air transmitters).

Main features:Remote hand free operation of air switches. Even in wet or hazardous environments, this pneumatic foot air pedal safely isolates the user operating power tools and other electrical devices from the electrical current. The foot air pedal provide the pulse air pressure needed to operate a remote air switchTwo switching logics are possible, depending of the air switch used:- Momentary Switching: Press and hold for on, release for off- Alternate Action Switching: Press for on, press again for offTypical applications: Electrical equipment remote operating of electrical devices on/off including motors, lights, pumps, air blowers, or other associated equipment.

Type R1B

Paddle flow switches, micro-switch contact; 3/4” BSPP union nut.

Main features:Water flow detection on water pipes Functional principle: Balanced paddle, perpendicular to the main flow, actuating a micro- switch. Flexible elastomeric gasket between paddle and electric switch

Type R1D

Paddle flow switches, micro-switch contact; 1/2” BSPP male thread.

Main features:Water flow detection on water pipes Functional principle: Balanced paddle, perpendicular to the main flow, actuating a micro- switch. Flexible elastomeric gasket between paddle and electric switch

Type R1Q

Paddle flow switches, micro-switch contact, 1/2” BSPP male thread, and Pt100 temperature sensor.

Main features:Water flow detection on water pipes, with simultaneous water temperature measurement Functional principle: Balanced paddle, perpendicular to the main flow, actuating a micro- switch. Flexible elastomeric gasket between paddle and electric switch. Temperature measurement is made by a plastic pocket located under the ½” thread

Type R1P

Paddle flow switches, reed switch contact, 3/4”union nut, slim design.

Main features:The most simple flow switch with magnetic pull-back. Recommended mounting position is on horizontal pipes, but can be mounted in any position. For water flow detection on dia. 25 to 100 mm water pipes

Type R1Q

Paddle flow switches, reed switch contact, inside barbed tee for 1”soft tube.

Main features:Tee equipped with paddle flow switch, for spas and swimming pools applications, mounting on 1” (20 to 21mm ID) soft PVC tubes, adjustable setting.Used on water circulation circuits to detect the passage of water or filter clogging and avoid dry running.Recommended mounting position is on horizontal pipes, but can be mounted in any position allowing an efficient air bleed.

Type R1X

Paddle plastic switches, reed switch contact, external body.

Main features:General application in flow detection. . Recommended mounting position is on horizontal pipes, but can be mounted in any position. For water flow detection on dia. 15 to 100 mm water pipes

Type R1V

Paddle flow switches, reed switch contact; external brass body.

Main features:General application in flow detection. Recommended mounting position is on horizontal pipes, but can be mounted in any position. For liquids flow detection on dia. 15 to 100 mm pipes. Body and union nut in brass for improved mechanical strength and pressure resistance. Connection box with terminal block or connectors, and detection point adjustment screw

Type R36

Piston flow switches, reed switch contact, inlet and outlet 3/4” BSPP male.

Main features:Product developed for electrical or gas instantaneous water heaters. 3/4 “ BSPP male water inlet and outlet. Mandatory vertical mounting, with water inlet from the bottom. Built-in over-pressure valve

Type DM

Vertical mounting level switch, reed switch contact, polypropylene stem with M8 thread, dia. 20 x 16.4 mm EPS foam float.

Main features:vending machines, air conditioning pumps, dehumidifiers. Small diameter float for reduced space applications. EPS foam float avoid float leaks, but reduces the maximum liquid temperature.

Type DT

Horizontal mounting level switch, reed switch contact, PBT stem, hollow PBT float, ½”NPT thread.

Main features:steam generators, coffee machines, vending machines, air conditioning pumps, dehumidifiers, tanks. The side mounting allows to adjust the level on big size tanks.

Type Q88F

Mechanical humidistats for incorporation, front shaft adjustment.

Main features:They use hygroscopic polymer film with special treatment, guaranteeing a fast response, long lifetime and high stability SPDT or SPST contact

Type Q88S

Mechanical humidistats for incorporation, side shaft adjustment.

Main features: They use hygroscopic polymer film with special treatment, guaranteeing a fast response, long lifetime and high stability SPDT or SPST contact

Type Q88F-R

Wall mounting mechanical room humidistats, Universal use.

Main features: They use hygroscopic polymer film with special treatment, guaranteeing a fast response, long lifetime and high stability SPDT contact

Type Q7C

DIN rail mounting miniature humidistat for cabinet air control.

Main features: This humidistat is designed to switch on a heater or a ventilating fan It can also be used to switch on humidifiers, dehumidifiers, or other devices. It must be mounted in a ventilated area.

Types: Q8WHH

Electronic on-off relative humidity and temperature controllers with IP 65 enclosure for green house and farms.

Main features: Temperature and relative humidity display or control in cold rooms commercial applications, green house and farming

Type 5EA

Fire detection fusible links 2 holes dia 11.5mm distance 43.5mm.

Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5ED

Fire detection fusible links 2 holes dia 5.2mm distance 16mm.

Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EE

Fire detection fusible links 2 holes dia 6.9mm distance 23.7mm.

Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EF

Fire detection fusible links 2 holes dia 7mm distance 95mm.

Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EG

Fire detection fusible links distance 9.6mm

Main features: A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EH

Fire detection fusible links 2 holes dia 7mm distance 95mm.

Main features:A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EJ

Fire detection fusible links 2 holes dia 6.9mm distance 46mm.

Main features:A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5ET

Fire detection fusible links 2 holes dia 10.3mm distance 59.6mm.

Main features:A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EV

Fire detection fusible links 2 holes dia 6.3mm distance 32mm.

Main features:A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EW

Fire detection fusible links 2 holes dia 5.4mm distance 30.5mm.

Main features:A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type 5EZ

Fire detection fusible links 2 holes distance 11.4mm.

Main features:A fire detection fusible link is a mechanical component that breaks at a preset temperature. They are used in fire protection systems to open and close doors, vents, dampers, valves if the ambient temperature exceeds a certain value.

Type BN

6 mm² Glazed ceramic connection blocks. Nickel plated connectors.

Main features:Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles

Type BV

4 mm² Glazed ceramic connection blocks. Nickel plated connectors.

Main features:Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles

Type BP

10 mm² Glazed ceramic connection blocks. Nickel plated connectors.

Main features:Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles

Type BQ

16 mm² Glazed ceramic connection blocks. Nickel plated connectors.

Main features:Ceramic: Ker 110 glazed 5 sides. Available in 1, 2, 3, 4 poles

Type BC

High Temperature (500°C) Ceramic Terminal Blocks, with Stainless Steel terminals and screws.

Main features:These high quality electrical connection blocks allow efficient and easy wiring connections of ovens, infrared heaters, quartz tube heaters in furnaces, kilns, catering equipment. • Designed for increased resistance to permanent high temperature, they can withstand long term temperatures of 900°F (500°C) and 1292°F (700°C) during short time periods. • Terminal screws are provided with a stainless steel elastic washer to avoid loosening by thermal cycles• Rating: 32A per terminal Available in 2 and 3 pole

Type BD

High Temperature (500°C) Ceramic Terminal Blocks, with Stainless Steel terminals and screws, heat conduction protection, and wire protection.

Main features:These high quality electrical connection blocks allow efficient and easy wiring connections of ovens, infrared heaters, quartz tube heaters in furnaces, kilns, catering equipment. • Designed for increased resistance to permanent high temperature, they can withstand long term temperatures of 900°F (500°C) and 1292°F (700°C) during short time periods. • This BD type has 4 legs to avoid thermal conduction with the mounting board and a cable bending protection blade on saddles • Terminal screws are provided with a stainless steel elastic washer to avoid loosening by thermal cycles • Rating: 32A per terminal Available in 2 and 3 pole

Type BEM

High temperature grommet.

Main features:High temperature ceramic cable grommet for kilns. Metal nut. Maximum temperature 300°C

Type BR

Multiple poles ceramic connection blocks.

Main features:Designed for increased resistance to permanent high temperature, they can withstand long term temperatures of 900°F (500°C) and 1292°F (700°C) during short time periods. • Saddle terminals screws are provided with a stainless steel elastic washer to avoid loosening by thermal cycles • Rating: 32A per terminal

Type BY

Cylindrical connection block.

Main features:3 ways ceramic block. Nickel plated brass M3 screw terminal, without pressure plate, for wires up to 3mm maximum diameter. Maximum temperature 230°C